Introduction to the principle and use of ice machine

Introduction to the principle and use of ice machine

Today, when the economy tells development, ice machines are widely used in all walks of life. So, do you know about ice machines? Here's a look at you:

The ice making principle of the ice machine:

1. The chilled water of the water storage tank is continuously circulated through the plate or the compartmental evaporator by the water pump;

2. After the compressor is running, it is inhaled - compression - exhaust - condensation (liquefaction) - throttling - and then vaporized by evaporation at a low temperature of -10 ° C to -18 ° C in the evaporator. The chilled water continuously condenses into an ice layer on the surface of the lower temperature evaporator at a water temperature of 0 °C. When the ice layer condenses to a certain thickness, after the evaporation temperature of the refrigerant reaches the temperature control set temperature, the defrosting solenoid valve is often turned on and the heat pump is used to de-ice, and the next cycle is realized.

Ice machine installation instructions:

1. Placement of ice machine

(1) This unit should be placed in a place where air is circulated and clean around.

(2) This machine should not be placed in the open air, and should not be exposed to direct sunlight or rain. You can't get close to the heat source around.

(3) The environment in which the machine is used must not be lower than 5 ° C and not higher than 38 ° C.

(4) There should be enough space around the machine, especially the back can not be less than 250mm. So that the machine is cooling.

(5) Separate model installation Please adjust the grounding screw at the bottom of the machine with the level gauge to make the machine level stable.

2, the installation of the water system

(1) Please connect the water source that meets the local drinking water standard.

(2) Attach a filter if necessary to increase the drinking standard of water.

(3) The water supply system must meet the following conditions: the water temperature is lower by 2 °C, the higher is not more than 38 °C, the water pressure is lower than 0.02 Mpa, and the higher is 0.8 Mpa;

3, the installation of the power supply

(1) The power supply must be the same as indicated on the machine nameplate.

(2) All lines must comply with national standards.

(3) Must be reliably grounded, the grounding wire must meet electrical standards.

(4) The voltage fluctuation shall not exceed ±10% of the rated voltage.

Ice machine features:

1. Using an effective evaporator, the ice is made quickly and the ice cubes are crystal clear.

2, high-performance compressor, forced air cooling, cooling system optimization design, can fully meet the needs of ice making.

3, intelligent design, a variety of protection modes, the ice making process is completed automatically, and the system operation can be optimized according to different environmental temperatures. 4, fully enclosed structure to ensure the health of the machine and ice.

5. The microcomputer monitoring system can smoothly carry out the ice making cycle.

6. The temperature sensor detects the ice full automatic stop, automatically turns on the ice block, and the control mode is reliable.

7, the size of the ice block is adjustable, to adapt to different ice occasions.

8, user-friendly operation interface, work prompt function, easy to use. Through the above introduction, I believe that everyone has already understood the principle and use of the ice machine. To purchase a snowflake ice machine, please choose the YKKY brand FM snowflake ice machine provided by Beijing Changliu. Welcome to inquire.

Profile Measuring Instruments

Roughness profiler all-in-one machine is an all-in-one machine for measuring profile shape and surface roughness, which has the powerful function of analyzing and measuring profile shape and surface roughness. Realize accurate measurement of dimensions, shape and roughness. It is mainly used to measure the parameters of the surface micro-geometry and macro-geometry of mechanical parts such as straightness, inclination, angle treatment, roundness treatment, double-groove treatment, double-arc treatment, etc.

Performance characteristics
1. High accuracy, high stability and high repeatability: meet the measurement accuracy requirements of the measured part.
1) Select high-precision grating measurement system and high-precision inductance measurement system, with high measurement accuracy;
2) Independently researched and developed high-precision grinding guide rail system, which has good wear resistance of guide rail materials and ensures stable and reliable operation of the system;
3) High-performance linear motor drive system ensures high measurement stability and good repeatability.
2. Intelligent management and detection software system:
The operation interface of the instrument is friendly, the operator can easily master the operation of the instrument, and the use is very simple.
1) The company has accumulated many years of practical measurement software design experience to provide customers with simple, practical and fast operation experience;
2) The company has invested many years of human resources in the development of instrument software, with special software copyright;
3) With powerful functions, it can automatically process data, print reports in various formats, and automatically display, print, save and query measurement records;
The data can be archived or printed in a centralized manner, which does not take up the verification operation time;
4) The measurement range is wide, which can meet almost all types of workpiece profile measurement, including special measurement functions of special workpiece screw, bearing, thread and other profiles;
5) The measured section can be selected automatically and manually for evaluation, and software functions can be customized according to customer requirements;
6) Powerful CNC automatic measurement and automatic labeling analysis function;
For large quantities of the same type of workpiece, it can carry out CNC measurement, automatically analyze and process the data, and carry out SPC statistics on the data, and can carry out statistical analysis in various ways to give quality control guidance;
7) It can automatically record and save all verification results by using computer large-capacity database storage.
3. It can also measure surface roughness and contour shape
With the same main body, you can only switch different modules to measure the profile shape and microroughness of the product.
4. Multi-parameter evaluation
The roughness can be automatically evaluated according to different standards, including Ra, Rp, Rv, Rz, Rt, Rmax, Rq, Rsk, Rku, RSm, RPc, Rdq, Rdc, Rmr and P parameters, W parameters, Motif parameters, Rcore parameters and other multi-parameter evaluation.
5. Thickness parameter measurement
When measuring the roughness parameters, the height and thickness of some film steps within 600 microns can be measured simultaneously. The measurement is convenient, and the accuracy is controlled within 2% H (H, the total height of measurement). It is especially suitable for high-precision measurement occasions without scratches.
6. Measuring force system:
With the voice coil motor force measuring system, the force measurement can be continuously adjustable from 10 to 150 mN, and the force measurement resolution can reach 0.2 mN; It avoids the force measurement error caused by the vibration of the surrounding environment when the old weight is loaded, and reduces the measurement error caused by the change of the force measurement.
7. Intelligent protection system:
The instrument is protected by hardware and software in all directions, which can effectively protect the instrument host and probe, and reduce the probe and instrument damage caused by personnel's operation errors.
8. Flexible manual control:
The instrument is equipped with a special separating operating rod, which can be placed at any position to control the operation when the instrument is operated and moved, and the measuring needle can be roughly positioned before measuring the workpiece; In the case of leaving the computer, the operating rod has the functions of moving the measuring needle left and right/up and down, emergency stop, the angle swing of the measuring rod up and down, and multi-level speed adjustment.

Profile Measuring Instruments,Profilometer Accuracy,Profile Measuring Machine,Surface Profile Measurement

Zhejiang dexun instrument technology co., ltd , https://www.dexunmeasuring.com