Energy-saving ceramic fiber muffle furnace technical parameters: model Studio size Rated temperature °C Rated power (KW) voltage Remarks SX3-1.5-10 165*120*105 1000 ° C 1.5 220V 50HZ SX3-2-12 165*120*105 1200 ° C 2 SX3-2-13 165*120*105 1300 ° C 2 Double outer casing SX3-3-10 300*200*150 1000 ° C 3 SX3-3-11 300*200*150 1100 ° C 3 SX3-3-12 300*200*150 1200 ° C 3 SX3-3-13 300*200*150 1300 ° C 3 U-shaped silicon carbon rod heating double shell SX3-4-10 300*300*300 1000 ° C 4 SX3-4-12 300*300*300 1200 ° C 4 SX3-4-13 300*300*300 1300 ° C 4 U-shaped silicon carbon rod heating double shell SX3-5-10 400*400*400 1000 ° C 5 SX3-7.5-12 400*400*400 1200 ° C 7.5 380V 50HZ Four-sided heating lining furnace bottom plate double shell SX3-6-13 400*400*400 1300 ° C 6 U-shaped silicon carbon rod heating double shell SX3-7.5-10 500*500*500 1000 ° C 7.5 Four-sided heating lining furnace floor SX3-8-11 500*500*500 1100 ° C 8 Four-sided heating lining furnace bottom plate double shell SX3-4-16 200*150*150 1600 ° C 4 220V 50HZ Silicon molybdenum rod heating 2. The operation of the empty furnace test push rod mechanism, the tie rod mechanism and the lifting mechanism. 3. Loosen the compression spring to the specified size range. 4. Adjust the water level of the water seal, open the valve through which the water seal is discharged, and close the valve through the water seal. 5. Close the furnace door at the feeding end, open the furnace door at the discharge end, and close the furnace door when the kerosene is sprayed out to form a misty flow. 6. Point the burner of the feed chamber. 7. Exhaust gas should be discharged through a valve that does not pass through the water seal. 8. Intermittent production first carburizes the furnace. 9. When the part is placed, the distance between the part and the part is not less than 5 mm; the edge of the part does not exceed the length of the base plate and the specified height. 10. To quickly switch the feed and discharge doors, but the speed of the push-pull rods should be smooth. 11. The position of the part in the pre-cooling chamber should be right below the thermocouple. 12. Only 24 chassis can be filled in the furnace, and the feeding must be pulled first and then pushed. 13. When the furnace is shut down, the furnace zone should be lowered to the same temperature, and then the natural cooling will begin. 14. Muffle furnace equipment cleaning: 15. After quenching the chassis or fixture, return to the pre-cooling chamber to remove oil. 16. It is found that the exhaust pipe is blocked (the pressure in the furnace is suddenly increased) and should be cleaned up immediately. First open the exhaust valve that does not pass the water seal, and then close the exhaust valve of the water seal. After cleaning, open the exhaust pipe valve of the water seal first, and then close the exhaust valve without water seal. 17. Muffle furnace notes: (1) Always pay attention to the combustion conditions of various districts and the pressure of gas; (2) When the furnace door is opened, it cannot stand in the middle to prevent the flame from being burned; (3) Pay attention to whether the burner of the department is burning and check whether the wedge door is leaking with a torch; (4) When the flame of the burner is extinguished during work, the gas valve should be closed immediately, and then the air valve should be closed; (5) If the part is dropped during work or the wedge-shaped door switch is not working, the feeding should be stopped and the parts removed. Shangyu Xingxing Instrument Equipment Co., Ltd. is located in Daoxu Town, Shangyu District, Shaoxing City, Zhejiang Province. It is an enterprise integrating production, product research and development, processing and trade. The company's main products: drying box series, incubator series, laboratory muffle furnace series, distilled water series, as well as clean workbench, air shower, fume hood, biological safety cabinet and other complete purification equipment. The company has a strong technical research and development team, a strong after-sales guarantee service system, is the linger of the Chinese laboratory complete sets of equipment manufacturers, welcome customers to buy. Industrial Applications Nitrile Gloves Industrial Applications Nitrile Gloves,Industrial Nitrile Gloves,Food Grade Disposable Gloves,Food Grade Nitrile Gloves Puyang Linshi Medical Supplies Co., Ltd. , https://www.linshimedicals.com Energy-saving ceramic fiber muffle furnace operating procedures:
Energy-saving ceramic fiber muffle furnace operating procedures
Next Article
Cultivation of Colored Cabbage